- Oracle RAC 188.8.131.52 - 2 Node Cluster Solution for ZCM
... is not lost. In simple words, it provides superior fault tolerance , load balancing , and highest scalability . ...
Article - kmegha - 9 Jul 2012 - 10:02am - 3 comments - 1 attachment - 2 groups
- Operations Center - Clustering & High Availability
... configured in a manner that it has some level of Fault Tolerance (FT) and/or HA which in turn reduces the possibility of outages ... helps with HA, but FT is not HA. (more on that later). Fault Tolerance (FT) is more about configuring the hardware of a system in a ...
Article - tisenberg - 26 Apr 2012 - 10:30am - 0 comments - 0 attachments - 2 groups
- OES2 Rolling Cluster Upgrade from NetWare - Part 4 - iPrint Migration
... Testing iPrint on OES2 eDir Replica fault tolerance Enable Auditing Check iPrint.ini file ... (see later section in this guide). eDir Replica fault tolerance Modify the /etc/opt/novell/iprint/conf/ipsmd.conf And the ...
Article - khurni - 7 Jul 2011 - 10:24am - 0 comments - 1 attachment - 4 groups
- OES2 Rolling Cluster Upgrade from NetWare - Part 2 - Migrating GroupWise
... Remember, my setup has two GWINTER/Agents and I desire fault tolerance for them, so that's why I have two entries for my GWAP ...
Article - khurni - 7 Jul 2011 - 10:22am - 1 comment - 1 attachment - 5 groups
- Optimising Linux servers for GroupWise and NCP Performance
... parameters can be set to improve the performance / fault tolerance on the Operating System / Novell services. Networking Configure the network to use NIC Bonding for fault tolerance. This greatly reduces the risk of losing connectivity should a ...
Article - peter6960 - 12 Apr 2011 - 11:05am - 2 comments - 0 attachments - 3 groups
- Install ZRS with Oracle 10g R2 on SLES 10 SP3 with ZCM 10.3.x
... (based upon our size). This will also give us a fault tolerance ZCM Primary server environment. This is document is ... than one primary server in a ZCM Zone. This gives fault tolerance (in case a primary server is down, the other primary can ...
Article - khurni - 1 Apr 2011 - 9:17am - 7 comments - 1 attachment - 4 groups
- Implementing Bonding with SLES 11 on XEN Virtual Guest Machines (OES2 SLES 10 SP2) Using the GUI Interface
... GUI interface to provide load balancing and fault tolerance . There are other very good notes related to bonding ... for the virtual guest machines to load balance and have fault tolerance. At the time of this writing, the following versions of ...
Article - npelton - 21 Aug 2009 - 3:06pm - 0 comments - 1 attachment - 3 groups
- Running ZENworks Configuration Management on a Cluster
... / node . One reason is that ZCM has built-in fault tolerance through content replication and closest server ...
Article - ssalgy - 23 Jun 2009 - 12:19pm - 2 comments - 0 attachments - 3 groups
- Consultant's Corner: Upgrading to GroupWise 8 - Part 2: Domains
... to have at least 2 domains in your environment for fault tolerance and recovery. Ideally, your Secondary domain(s) will hold ... post offices or gateways and hopefully not both, again for fault tolerance/recovery reasons. In my case, I will assume my Secondary ...
Article - GreggHinchman - 5 Mar 2009 - 11:25am - 0 comments - 0 attachments - 3 groups
- Clustering within clustering
... application data separate adds greater flexibility and fault tolerance . The example below shows four physical blades (in red) ...
Article - samprior - 27 Feb 2009 - 10:49am - 2 comments - 0 attachments - 2 groups